Top-hat rail, 35 x 7.5 mm, steel, 100 cm
Aluminium mounting clip for top-hat rail, W 54mm
KKSB Arduino DIN rail bracket, powder-coated steel, black
PCB holder for top-hat rail 10cm long
PCB holder for top-hat rail 15cm long
Top-hat rail mounting kit for single-board computers or 3.5" devices
Top-hat rail, 35 x 15 mm, steel, 25 cm
KKSB DIN rail clip for 35mm top-hat rail, coated aluminium, black
Top-hat rail, 35 x 15 mm, steel, 100 cm
Top-hat rail clip for circuit board, 4 pieces
Content: 4 Stück (€2.73 / 1 Stück)
PCB holder for top-hat rail 20cm long
DIN rails, holders and clips for the cabinet
The DIN rail is the least conspicuous standard in electrical engineering and one of the most useful: a standardised metal profile onto which components simply snap. Here you will find DIN rails in various lengths and profile heights, mounting clips, board holders and brackets for single-board computers — everything needed to get your own electronics tidily into a distribution board or control cabinet.
35 x 7.5 or 35 x 15 — the profile height matters
The width is always 35 mm, the standard to which every component refers. What differs is the height of the profile: the shallow version at 7.5 mm is the standard and what is fitted in practically every consumer unit. The tall version at 15 mm is considerably stiffer in bending and is used where heavy components span a longer distance — large power supplies, contactors, isolating transformers.
Snap-on devices fit both. The difference lies in deflection and in the depth taken up: the 15 mm rail stands 7.5 mm further out, which can already be tight in shallow enclosures.
Lengths run from 25 cm through 50 cm to 100 cm, plus a version in 19 inch width for rack mounting and shorter sections at 160 and 235 mm for small enclosures. Rails can be shortened with a hacksaw — deburr the cut edge thoroughly, as sheet metal edges are sharp and a burr stops the next module snapping on cleanly.
Clips and holders: getting your own electronics onto the rail
The commonest case in home automation: you have a board, a relay module or a small computer and want both inside the distribution board without improvising. There are three routes.
The board holders in lengths from 5 to 100 cm take a circuit board by its edge and clip onto the rail. That is the most direct solution for boards you have built yourself — you choose the length to suit the board width. The DIN rail clips for boards in packs of four work the other way round: they are screwed to the board and so make the board itself snap-mountable.
The aluminium mounting clips at 27 and 54 mm wide and the spring clip at 50 mm are the universal option for anything with a surface to screw to. The universal DIN rail holder and the mounting kit for single-board computers or 3.5 inch devices are matched to that very form factor — a Raspberry Pi or a small industrial enclosure then sits firmly and removably. For Arduino there is a dedicated bracket in powder-coated steel.
What to watch out for in a cabinet
Three points that make the difference between a tidy installation and an annoying one.
Heat rises. Power supplies and anything that gets warm belong in the upper row and need space — a switched-mode supply wedged between two modules shortens its life considerably. Leave air, and if in doubt check after an hour of operation by hand or with an infrared thermometer.
Plan in modules. Distribution board components are counted in modules of 17.5 mm, the European standard width to DIN 43880. Home-made brackets do not observe it, and then the cover plate no longer fits. Measure the actual width of your assembly before populating the rail.
In many installations the DIN rail is earthed. A board resting directly on the rail can pick up an unintended ground connection through it — or, in the worse case, a short circuit. The holders here maintain the necessary clearance; with a design of your own an insulating spacer belongs in between.
And one note that needs no explanation but should be said anyway: work on the mains side of a distribution board belongs in the hands of a qualified electrician, and in several countries it is legally reserved to one. What you can build and snap in yourself is everything running on low voltage — and in home automation that is by far the larger part.