Adafruit S-35710, Low-Power Wake Up Timer Breakout, 24-bit second counter, programmable alarm
Adafruit ADS1115 16-bit ADC - 4 channel with programmable amplifier
MCP4725 DAC digital-to-analogue converter breakout board, I2C
ADS1115 4-channel 16-bit AD converter breakout board
Adafruit TCA4307 Hot-Swap I2C Buffer with Stuck Bus Recovery
Adafruit MCP4725 Breakout Board - 12-Bit DAC with I2C Interface
Soldered MCP23017 I2C IO Expander, Qwiic, 16 digitale Ein-/Ausgänge, 8 Adressen, 2x Qwiic
4-channel I2C-compatible bi-directional logic level converter
Soldered Logic-Level-Converter-Modul 5V zu 3,3V, Pegelwandler für digitale Signale
Soldered MAX232 RS-232 Modul, 2 Kanäle, Full-Duplex, TX/RX, Pegelwandler, 3,3–5,5 V
Soldered MCP47A1 6-Bit 1-Kanal DAC Breakout, I2C, Qwiic Adapter, 1,8–5,5V
Soldered TCA9548A I2C-Multiplexer Qwiic, 8 Kanäle, bis 64 Geräte, Breakout Board
MAX3232 RS232 zu TTL Serial Port Konverter Modul, Mini
Adafruit DS2413 1-Wire Controller Breakout with 2 GPIO
Adafruit ADS1015 12-bit ADC - 4 channel with programmable amplifier
DFRobot Gravity 2-Kanal-I2C-DAC-Modul, I2C, 12 Bit, 0-10-V-Ausgang, GP8403, bis zu 16 Geräte, 3,3-5V
Level shifters, converters and multiplexers between 3.3 and 5 volts
Two components that are supposed to understand each other often run at different logic voltages — and then you need a module in between. This is where the breakouts for those jobs live: level converters for voltage matching, analogue-to-digital converters, digital-to-analogue converters, multiplexers and port expanders.
3.3 volts meets 5 volts
The level shifter is the most common module in this category, and the reason is printed on every Raspberry Pi: its GPIO pins work at 3.3 V and do not merely dislike 5 V, they will not take it at all — a 5 V signal can destroy the pin. For digital lines there is the bidirectional level shifter with four and eight channels, the TXB0104 and the TXS0108E with eight channels. Specifically for I2C there are the PCA9306 and an I2C-capable four-channel version, and the difference matters: a simple transistor shifter will not carry an open bus with its pull-ups cleanly across the boundary. From Soldered come modules with the TXS0104 and TXB0104 in the same form factor.
Analogue into numbers
Microcontrollers without a usable analogue input — the ESP32 has an imprecise one, the Pi none at all — get an external ADC. The ADS1115 resolves 16 bits on four channels and has a programmable gain amplifier; the ADS1015 works at 12 bits and is faster. One special type accepts voltages from minus 24 to plus 25 V, so negative ones and ones above the supply. The PCF8591 combines an eight-bit input with an output, and the Grove ADC module with an ADC121C021 is the pluggable variant. For the other direction there are the DAC breakouts: the MCP4725 with 12 bits, the MCP4728 as a quad version with EEPROM, and DFRobot's GP8403 module, which outputs 0 to 10 V directly — the signal format of industrial controls and dimmers.
More pins, more addresses
When you run out of pins, a port expander helps. The MCP23017 brings 16 digital inputs and outputs over I2C, the SX1509 adds LED driving, and the Waveshare variant has PH2.0 connectors instead of just solder pads. The second classic problem is duplicate addresses: two identical sensors on the same bus cannot be told apart. That is what the I2C multiplexer TCA9548A is for, switching eight separate bus branches and making up to 64 devices reachable. For analogue signals the CD74HC4067 with 16 channels and the 74HC4051 with eight do the job. The TCA4307 is a buffer that frees a bus blocked by a hung device.
Isolating, measuring, converting
For jobs beyond level shifting there are special parts. The USB logic analyser from SparkFun records eight channels at 24 MHz — the tool that shows you whether an I2C command even reaches the line, instead of guessing in your code. The MAX3232 module converts the RS232 levels of a serial interface to TTL, and Soldered offers the same as a MAX232 variant with two channels. An optocoupler breakout isolates two circuits galvanically, and the op-amp breakout with an LMV358 amplifies a weak analogue signal before the converter. The S35710 is a wake-up timer with a seconds counter for builds that should sleep between two measurements.