Waveshare ESP32-S3-Zero M S3FH4R2, Dual-Core, 240MHz, Wi-Fi & BT 5, USB-C, without header

Product number: WS-25081

€6.90

Content: 1 Stück

Currently not available

Notify me when the item is available.

Privacy

By selecting continue you confirm that you have read our and accepted our .

€6.90

Waveshare ESP32-S3-Zero M S3FH4R2, Dual-Core, 240MHz, Wi-Fi & BT 5, USB-C, without header

Content: 1 Stück

Order now and secure 4 Berrys

Product information "Waveshare ESP32-S3-Zero M S3FH4R2, Dual-Core, 240MHz, Wi-Fi & BT 5, USB-C, without header"

ESP32-S3-Zero development board
Based on the ESP32-S3FH4R2 dual-core processor, this development board offers a running frequency of 240MHz and supports 2.4 GHz Wi-Fi and Bluetooth 5. The ESP32-S3-Zero development board has multifunctional GPIO pins and is particularly suitable for SMD applications thanks to its stamped module structure. Due to its offset holes, it is small and easy to integrate into other host boards. The ESP32-S3-Zero has an integrated Type-C USB port, offers many unused pins in a small design and uses the ESP32-FH4R2 as the system chip (SoC).

Features at a glance

Equipped with the Xtensa 32-bit LX7 dual-core processor with up to 240MHz main frequency
Supports 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth® 5 (LE)
Integrated 512KB SRAM and 384KB ROM, on board 4MB flash memory and 2MB PSRAM
Stamped module and integrated ceramic antenna allow direct soldering on carrier boards
Supports flexible clocking, independent module power supply setting and other controls for low power consumption in various scenarios
Integrated with USB serial port full-speed controller, 24 × GPIO pins for flexible pin function configuration
4 × SPI, 2 × I2C, 3 × UART, 2 × I2S, 2 × ADC, etc.

Technical data

ESP32-S3FH4R2 dual-core processor: up to 240MHz operating frequency
USB Type-C port
ME6217C33M5G: Low dropout LDO, 800mA (max)
WS2812 RGB LED
2.4G ceramic antenna
BOOT button: Press it and then the RESET button to enter download mode
RESET button
ESP32-S3FH4R2 Pins

Hardware description

When using the ESP32-S3-Zero with daughter boards, avoid covering the ceramic antenna with PCB boards, metal or plastic components.
In the ESP32-S3-Zero, pins GPIO33 to GPIO37 are not accessible; these pins are used for Octal PSRAM.
The ESP32-S3-Zero uses GPIO21 to connect to the WS2812 RGB LED. Please refer to [the documentation link] for WS2812 specifications.
The ESP32-S3-Zero does not use a USB-to-UART chip. When uploading the firmware, press and hold the BOOT button (GPIO0) and then connect the Type-C cable.
The "TX" and "RX" markings on the board indicate the standard UART0 pins for the ESP32-S3-Zero. More precisely, TX is GPIO43 and RX is GPIO44

Scope of delivery

1x ESP32-S3-Zero

Wiki: https://www.waveshare.com/wiki/ESP32-S3-Zero

Zolltarifnummer:	85269200
Brand:	Waveshare
Country of Origin:	China
EAN:	4060137087387
Gross Weight (kg):	0.004
Manufacturer ID:	ESP32-S3-Zero
Product ID:	WS-25081

Waveshare

Waveshare: High quality modules for your Raspberry Pi

Waveshare is a reliable specialist when it comes to displays, cameras and other modules for your Raspberry Pi. With the products of the innovative electronics expert, you can turn your computer into a true all-round device.

Waveshare provides an optimal view

You are looking for the ideal display module for your Raspberry Pi? At Berrybase you will find a wide range of products from Waveshare. Each display and all associated modules have been designed with the utmost precision and meet the highest demands - no matter what purpose the respective product is supposed to serve.

For example, the Waveshare ePaper HATs offer perfect conditions if you want a high display quality even in strong sunlight. A big advantage of ePaper displays is their extremely low energy consumption. The best example is the 2.13" 250×122 ePaper Display HAT with integrated controller, which is optimally tailored to the Raspberry Pi 2B, 3B, Zero and Zero W. The communication with this module is done via SPI interface. The ePaper display equipped with the HAT is limited to the colors black and white and reflects light like conventional paper. This is good for the display quality.

If you prefer a display in the three colors red, black and white to complement your Raspberry Pi, the 2.7" 264×176 ePaper Display HAT is recommended. It has the same technical features as the other Waveshare ePaper HATS.

Compact and of brilliant quality: The Waveshare 7 inch Display

The Waveshare 7 inch display, on the other hand, scores not only with its compact design, but also with a 1024x600 hardware resolution and capacitive touch control. On all devices with Raspberry Pi OS, the 7 inch LCD even works driver-free. The integrated 3.5mm jack enables sound output, while the image is produced via an HDMI connection. The impeccable quality manifests itself in a high-quality glass surface with a 6H hardness level.

At Berrybase, you can get the display including a robust case on request - so that it is optimally protected against external influences. Besides the Waveshare 7 inch display, the electronics specialist also has many other screens in different sizes available.

Waveshare Game HAT: Turning your Raspberry Pi into a game console

One of the top sellers at Berrybase is the Waveshare Game HAT for the Raspberry Pi. The controller transforms your computer into a mobile game console. The 3.5" IPS display convinces with a 480×320 resolution and ensures smooth image playback and thus unlimited gaming fun. The sound is reproduced via on-board speakers or optionally via the 3.5 mm jack socket. The battery of the Game HAT is charged via the integrated charging circuit. The module is compatible with the Raspberry Pi models A+, B+, 2B, 3B and 3B+. For other versions the connection via HDMI cable is possible.

If you want to turn your Raspberry Pi into a mobile retro console, we recommend the GamePi43 with a 4.3-inch IPS display, which is suitable for the Raspberry Pi models B+, 2B, 3B and 3B+, or the especially compact GamePi20. The latter features a 2.0-inch IPS display and is compatible with the Raspberry Pi Zero 1.3, Zero W as well as the Zero WH.

Practical accessories for every purpose

By the way: Waveshare's product range is also peppered with useful accessories for your Raspberry Pi. The Li-Ion battery HAT for example provides a mobile power supply for your computer. The 8 channel DIN rail relay module from Waveshare allows you to use your Raspberry Pi as a control module for tech projects in the home, for example to centrally control the home lighting or shutters. And with the Ethernet / USB HUB HAT, Waveshare has designed a module that extends the USB capability of your Raspberry Pi and provides an RJ45 Ethernet port. The latter offers an enormous added value when a stable wired Ethernet connection is required.

Manufacturer information
Waveshare International Limited
2F, World Trade Plaza south side, Fuhong Rd
CN 518033 Futian District, Shenzhen
https://www.waveshare.com
[email protected]

WEEE number: 72769965

Responsible person for the EU
Sertronics GmbH
Am Studio 20d
DE 12489 Berlin
https://www.berrybase.de
[email protected]

Safety instructions

Avoid contact of the board with water, moisture or conductive materials.
Only connect the board to the intended voltage sources (usually 3.3V or 5V); overvoltage can lead to damage.
The board can generate heat during operation, avoid skin contact.
Only work in well-ventilated areas, especially when soldering or testing components.
Use suitable ESD protection (electrostatic discharge) when handling the board.
Switch off the power supply before making any changes to the circuit.
Do not leave the board unattended when it is externally powered.
Dispose of the board in accordance with local regulations for electronic waste.
Disconnect batteries or capacitors before disposing of the board.
Return damaged boards to certified recycling centres or collection points for electronics.